Web Orders Over $100 Ship Free. Enter Promo Code "SHIPFREE" for free UPS Ground Shipping at Checkout. (USA Only)

80-646-0001 MikroTest Ni 50 6 Automatic Coating Thickness gauge 0 - 50 micron - MIK/010810

Made in Germany
MikroTest Magnetic Coating Thickness Gauge
Click images to enlarge.

The MikroTest is the most widely used coating thickness gauge in the world over the last 40 years. The MikroTest complies with the highest technical standards of all analogue magnetic coating thickness gauges. This magnetic coating thickness gauge works on the magnetic attraction principle to measure all non-magnetic coatings on steel and galvanic nickel on steel.

The MikroTest is supplied in 11 different models to be suitable for every requested application. The balanced measuring system ensures accurate readings at any angle: horizontal, vertical and overhead. Also, the gauge allows measurements on curved surfaces. It is also able to provide you with precise measurements in tubes and on round parts due to the automatic operation.

The measurement of the coating thickness is based on magnetic attraction. The attractive force is related to the distance between a permanent magnet and a steel substrate. This distance represents the thickness of the coating under measure. The magnet is lifted from the surface by means of a spring connected to the magnet arm. The force needed to lift the magnet is directly related to the angle of rotation of the torsion spring. This measuring principle is also especially suited for electroplated nickel on copper, aluminum and other non-ferrous metals. This measurement principle ensures fully automatic measurement where no power supply or calibration is required.

MikroTest FM 5 Gage, Coating Thickness, 0 to 40 mils
New Part #: 80-638-0101
Old Part #: MIK/010100
NSN: 5220-12-327-2245

mikrotest fm5 coating thickness gauge

Mikrotest Demo Video

1. Adjust dial to value higher than the expected thickness
2. Place gauge on surface to be measured
3. Press button on bottom of handle take make the magnet adhere to surface
4. Slowly turn wheel backwards until you hear a click and the magnet lifts
5. Read thickness value.

Features

  • Mils Models Include a NIST traceable calibration certificate, Micron Models include factory "works" certificate
  • Highest accuracy with simplest operation
  • No calibration required
  • Simple set-up and measurement
  • All gauges operate without power or battery
  • One point measurement
  • Metal Housing provides protection from mechanical shocks
  • Metal Housing and measuring system is resistant to solvents
  • Automatic models control realease of magnet for highest accuracy and repeatability

MikroTest Models

TypeRangeTypical ApplicationToleranceMin SurfaceMin RadiusMin Base Thickness
GM
G
4 mils
100 micron
Electroplating and Paint on Steel± 1 μm or 5% of readingØ 20 mm5 mm convex/ 25 mm concave0.5 mm
FM
F
40 mils
1000 micron
Paint On Steel± 5 μm or 5% of readingØ 30 mmmm convex/ 25 mm concave0.5 mm
S3M
S3
8 - 120 mils
0.2 - 3 mm
Enamel, Paint on Steel5% of readingØ 30 mm15 mm convex/ 25 mm concave1.0 mm
S5M
S5
20 - 200 mils
0.5 - 5 mm
Enamel, Paint on Steel5% of readingØ 50 mm15 mm convex/ 25 mm concave1.0 mm
S10M
S10
0.1 - 0.4 inches
2.5 - 10 mm
Enamel, Paint on Steel5% of readingØ 50 mm15 mm convex/ 25 mm concave2.0 mm
S20M
S20
0.3 - 0.8 inches
7.5 - 20 mm
Enamel, Paint on Steel5% of readingØ 100 mm100 mm convex/ 150 mm concave7.0 mm
Ni50M
Ni50
2 mils
50 micron
Electroplated Nickel on Non-Ferrous± (1 μm + 5% of reading)Ø 15 mm5 mm convex/ 25 mm concave-
Ni100M
Ni100
4 mils
100 micron
Electroplated Nickel on Non-Ferrous± (1 μm + 5% of reading)Ø 15 mm5 mm convex/ 25 mm concave-
NiFe50M
NiFe50
2 mils
50 micron
Electroplated Nickel on Steel± (2 μm + 8% of reading)Ø 20 mm10 mm convex/ 25 mm concave0.5 mm

High Temperature Option

An Optional High Temperature Kit is offered (MK-HT) for using MikroTest models on surface temperatures up to 212°F (100°C). It can also be used on surface temperatures up to 572°F (300°C), but the MikroTest must be limited to less than 5 seconds of surface contact or damage will result. The MK-HT Kit consists of aluminum feet and sensor prism.

Related Products

Mikrotest Coating Thickness Standards
Click image for more info
Coated Metal Plates for Calibration of MikroTest Coating Thickness Gauge
SurfaTest Wet film coating thickness gauge
Click image for more info
Wet film coating thickness gauge SurfaTest

Complete Kit

The MikroTest is supplied with the following items:
- MikroTest gauge
- Hand strap
- Plastic carrying case
- Operating instructions

Specifications

Ambient Temperature-20 °C - 100 °C
Conforming StandardsDIN EN ISO 2178, DIN 50 982, ASTM B 499, E 376, D 1186, G 12, B 530, BS 5411, ISO 2361
DimensionsGauge: 215 mm x 55 mm x 29 mm Plastic carrying case: 235 mm x 185 mm x 46 mm
WeightCase incl. gauge approx. 560 g
Calibration ShimsHere are the two technical reasons why you cannot use plastic shims/foils plus zero plate to check calibration of MikroTest:
1. All Plastic Shims/Foils have a certain prestress which has the effect that they are slightly bent when the magnet lifts off and this effect is similar to the effect of a spring will cause inaccurate readings
2. The Plastic Shims/Foils have a certain electrostatic charge which also causes inaccurate readings.
Warranty1-Year

Downloads

Buy Now

Item Description Price
80-646-0001
MikroTest Ni 50 6 Automatic Coating Thickness gauge 0 - 50 micron - MIK/010810
$1,320.00
Accessories
NISTCAL
Upgrade to a New NIST Traceable Cert (Supplied Factory Certificate maybe a few months old)
$100.00
MK-HT
High Temperature Kit for Mikrotest, includes 2x Aluminum Feet and Sensor Grommet
$125.00
08-015-0030
Plastic Inset (grommet) for MikroTest 5 or 6
$9.00
08-019-0028
Plastic Feet for MikroTest 5 or 6, (Set of 2 feet)
$5.00
82-020-0020
Spare / Replacement Carrying Case for MikroTest
$45.00
08-019-0042
Display Lens/Crystal for MikroTest 5 and 6
$39.00
In stock
1 Week Lead Time (Estimated)
2-3 Week Lead Time (Estimated)
Lead Time Varies, Please contact us for availability.
Unavailable